saw bandpass filter F6701 part no. F6701 rev. date 2012-10-18 i t f co., ltd. 102-901, bucheon technopark 364, samjeong-dong, ojeong-gu, bucheon-city, gyounggi-do, korea 421-809 rev. nsni05-as02 1/8 4 4 5 3 2 1 5 6 6 3 2 1 1.27 0.1 0.64 0.1 1.90 0.1 1.00 0.1 1.40 0.15 3.80 0.15 3.80 0.15 features rf bandpass filter high attenuation no matching 50 w single-ended operation ceramic surface mounted device (smd) package rohs compliant package dimensions dimensions shown are nominal in millimeters body : al 2 o 3 ceramic lid : kovar, ni plated terminations : au plating 0.3 ~ 1.0 um, over a 1.27 ~ 8.89 um ni plating maximum ratings parameter unit minimum typical maximum operating temperature range c -40 25 85 storage temperature range c -40 25 85 power handling capability dbm - - 10 electrostatics sensitive device ( esd ) pin configuration 2 input 5 output 1, 3, 4, 6 case ground itf 6701
saw bandpass filter F6701 part no. F6701 rev. date 2012-10-18 i t f co., ltd. 102-901, bucheon technopark 364, samjeong-dong, ojeong-gu, bucheon-city, gyounggi-do, korea 421-809 rev. nsni05-as02 2/8 specifications fc = 670 mhz notes : 1) all specifications are based on the matching s chematic shown below, measured by agilent network a nalyzer and full 2 port calibration. 2) electrical margin has been built into the design to account for the variations due to temperature d rift and manufacturing tolerances 3) all attenuation measurements are measured relati ve to insertion loss minimum typical maximum unit center frequency ( fc ) - 670 - mhz insertion loss (668 ~ 672 mhz) - 2.5 4.0 db amplitude ripple (668 ~ 672 mhz) - 0.5 1.0 dbp-p absolute group delay (fc) - 100 - nsec group delay variation (668 ~ 672 mhz) - 50 - nsec vswr (668 ~ 672 mhz) - 1.5 2.0 relative attenuation 0.3 ~ 652 mhz 691 ~ 1140 mhz 1140 ~ 1500 mhz 1500 ~ 2500 mhz 40 40 35 30 50 50 40 38 - - - - db input/output impedance 50 ohms
saw bandpass filter F6701 part no. F6701 rev. date 2012-10-18 i t f co., ltd. 102-901, bucheon technopark 364, samjeong-dong, ojeong-gu, bucheon-city, gyounggi-do, korea 421-809 rev. nsni05-as02 3/8 input 50 output 50 matching schematic ( actual matching values may vary due to pcb layout a nd parasitics ) marking configuration itf 1) 6701 2) 1) manufacturer name 2) marking number
saw bandpass filter F6701 part no. F6701 rev. date 2012-10-18 i t f co., ltd. 102-901, bucheon technopark 364, samjeong-dong, ojeong-gu, bucheon-city, gyounggi-do, korea 421-809 rev. nsni05-as02 4/8 typical performance ( at 25 )
saw bandpass filter F6701 part no. F6701 rev. date 2012-10-18 i t f co., ltd. 102-901, bucheon technopark 364, samjeong-dong, ojeong-gu, bucheon-city, gyounggi-do, korea 421-809 rev. nsni05-as02 5/8 typical performance ( at 25 )
saw bandpass filter F6701 part no. F6701 rev. date 2012-10-18 i t f co., ltd. 102-901, bucheon technopark 364, samjeong-dong, ojeong-gu, bucheon-city, gyounggi-do, korea 421-809 rev. nsni05-as02 6/8 input / output vswr charts input / output smith charts
saw bandpass filter F6701 part no. F6701 rev. date 2012-10-18 i t f co., ltd. 102-901, bucheon technopark 364, samjeong-dong, ojeong-gu, bucheon-city, gyounggi-do, korea 421-809 rev. nsni05-as02 7/8 packing specification 1. reeling quantity : 1000 pcs / reel 2. taping structure : the tape shall be wound around t he reel in the direction shown below. tape specification 1. leader part and vacant position specification 2. tensile strength of carrier tape 4.4n/mm width 3. top cover tape adhesion 1) pull off angle : 0~15 2) speed : 300mm/min 3) force : 20~70g reel reel reel reel top cover tape top cover tape top cover tape top cover tape carrier tape carrier tape carrier tape carrier tape end end end end start start start start tape running direction vacant 150mm min. component contained vacant 150mm min. leader part 250mm min. 0~ 15 degree top cover tape direction of pull carrier tape
saw bandpass filter F6701 part no. F6701 rev. date 2012-10-18 i t f co., ltd. 102-901, bucheon technopark 364, samjeong-dong, ojeong-gu, bucheon-city, gyounggi-do, korea 421-809 rev. nsni05-as02 8/8 carrier tape dimensions [unit : mm] part direction reel dimensions [unit : mm] a 4.30 0.1 b 4.30 0.1 c 7.25 0.1 d 1.70 0.1 e 12.00 0.1 f 8.00 0.1 tape running direction
|
